Blog Archives
Search Blog Archives
Tag Archives: Cisco 3725 router
Multi-Area OSPF – Redundancy, Route Summarization, and LSA Filtering
In this lab, all routers except for R4 and R5 are Cisco 3725 routers [IOS 12.4(15)T10]. Routers R4 and R5 are Cisco 7200 routers [IOS 12.4(24)T]. Below is the network diagram for this lab.
Posted in Cisco, Labs, Networking, Protocols, Technology
Tagged ABR, Area Border Router, Cisco, Cisco 3725, Cisco 3725 router, Cisco 7200, Cisco 7200 router, Multi-Area OSPF, networking, Open Shortest Path First, OSPF, OSPF ABR, OSPF Area Border Router, OSPF redundancy, OSPF summary route, redundancy, summary route
1 Comment
Configuring eBGP Peers to Use a Loopback Interface
In this lab, I use two Cisco 3725 routers [IOS 12.4(15)T10] to configure eBGP peers using loopback interfaces. Below is the network diagram for this lab.
Posted in Cisco, Labs, Networking, Protocols, Technology
Tagged BGP, BGP neighbor, BGP neighbors, BGP peers, Border Gateway Protocol, Cisco, Cisco 3725, Cisco 3725 router, cisco router, Configuring BGP, eBGP, eBGP peers, peers
Leave a comment
Configuring OSPF with Multiple Areas
In this lab, I use three Cisco 3725 routers [IOS 12.4(15)T10] to demonstrate how to setup OSPF with multiple Areas. Below is the network diagram for this lab.
Posted in Cisco, Labs, Networking, Protocols, Technology, Troubleshooting
Tagged Area, Areas, Cisco, Cisco 3725, Cisco 3725 router, Multiple Areas, Multiple OSPF Areas, OSPF, OSPF area, OSPF Areas, router
Leave a comment
EIGRP – Best Path Selection
By default EIGRP uses bandwidth and delay of the line to determine the best path to a remote network. However, if desired, EIGRP can use a composite of four metrics: bandwidth, delay, reliability, and load. Maximum transmission unit (MTU) is … Continue reading
Posted in Cisco, Labs, Networking, Protocols
Tagged bandwidth, Cisco, Cisco 3725, Cisco 3725 router, Cisco 3725 routers, delay, delay of the line, EIGRP, EIGRP calculation, eigrp load balancing, Enhanced Interior Gateway Routing Protocol, equal cost load balancing, load balancing, router, routing table, topology table
Leave a comment
Setting-up Basic iBGP and eBGP on Cisco Routers
The Border Gateway Protocol (BGP) is a protocol used to make core routing decisions on the Internet. BGP is commonly mislabeled or referred to as an IP routing protocol. However, it is not a routing protocol; rather, it is a … Continue reading
Posted in Cisco, Networking, Protocols, Technology
Tagged AS, Autonomous Number, Autonomous Numbers, BGP, BGP table, Border Gateway Protocol, Cisco, Cisco 3725, Cisco 3725 router, eBGP, established, established state, External BGP, iBGP, Internal BGP, Multihomed, neighbor, neighbor relationship, Neighbors, ping, prefxes, redistribute connected, redistribute static, redistribution of static and connected routes into BGP, show ip bgp, show ip bgp summary, state
Leave a comment
EIGRP and OSPF Redistribution on Cisco Routers
This was a quick lab I threw together which I thought was pretty cool. In this lab I use five Cisco 3725 routers [IOS 12.4(15)T10] in which I have two groups of routers each on a different subnet and running … Continue reading
Posted in Cisco, Labs, Networking, Protocols, Technology
Tagged Cisco, Cisco 3725, Cisco 3725 router, cisco router, EIGRP and OSPF Redistribution, EIGRP Redistribution, EIRGP, OSPF, Redistribution, router
Leave a comment
Setup and Troubleshoot EIGRP
I discussed Enhanced Interior Gateway Routing Protocol (EIGRP) briefly in a prior blog, Load Balancing with EIGRP, however, in this lab I use two Cisco 3725 routers [IOS 12.4(15)T10] to demonstrate how to configure EIGRP; additionally, I’ll discuss some useful … Continue reading