Category Archives: Networking
Setup Telnet Access on Force10 Switches
I am going to use a Force10 S60 switch [FTOS 8.3.3.4] to demonstrate how to setup telnet access. To setup telnet access you first need to set an IP address on either a data port or a managment port so … Continue reading
Posted in Force10 Networks, Labs, Networking, Technology
Tagged Force10, Force10 Networks, mamangement port, managementethernet, router, S60, switch, telnet
Leave a comment
Creating a Link Aggregation Group (LAG) in FTOS
This lab demonstrates how to create a Link Aggregation Group (LAG) in FTOS on Force10 switches. A LAG in Force10’s FTOS is called a port channel and in Cisco’s IOS is called an EtherChannel. As described by IEEE 802.3ad, LAG … Continue reading
Posted in Force10 Networks, Labs, Networking, Protocols, Technology
Tagged dynamic port channel, etherchannel, Force10, Force10 Networks, Force10 S25P, Force10 S50V, FTOS, IEEE 802.3ad, LACP, LAG, Link Aggregation Control Protocol, Link Aggregation Group, port channel, router, S25P, S50V, static port channel, switch
5 Comments
How Perl/Python Scripts on Force10 S60 Switches Can Access the Internet
Let’s say you have a Force10 S60 switch [FTOS 8.3.3.4] hooked-up at a datacenter that currently has a console connection connected to a management switch that provides external Internet access. The natted IP address is 10.0.8.10/24 and the external IP … Continue reading
Posted in Force10 Networks, Labs, Networking, Perl, Programming Languages, Python, Technology
Tagged console, default route, external Internet access, Force10, Force10 Networks, management interface, management port, management route, management switch, nat, natted IP, perl, Python, router, S60, S60 Switch, switch
Leave a comment
Setup OSPF on Force10 Switches
For this lab, I use a Force10 E1200 chassis [FTOS 8.3.1.1] and a Force10 S60 switch [FTOS 8.3.3.4]. The objective is to setup a simple OSPF network. Loopback addresses are used to setup test networks.
Posted in Force10 Networks, Labs, Networking, Protocols, Technology
Tagged E1200, Force10, Force10 Networks, Force10 S60, FTOS, OSPF, Route Processing Module, router, RPM, S60, Sorce10 E1200, switch
1 Comment
Discovery Protocols on Cisco, HP, and Force10 Switches/Routers – CDP and LLDP
The Cisco Discovery Protocol (CDP) is a Cisco proprietary Data Link Layer network protocol used to share information about other directly connected Cisco equipment. CDP can also be used in place of dynamic routing protocols in simple networks. Cisco devices … Continue reading
Posted in Cisco, Force10 Networks, HP, Networking, Protocols
Tagged 2621XM, CDP, Cisco, Cisco 2621XM, Cisco Discovery Protocol, Force10, Force10 Networks, Force10 S60, HP, HP Procurve, IEEE 802.1AB, Link Layer Discovery Protocol, LLDP, Procurve, S60
2 Comments
Setup Inter-VLAN Communication via “Router on a Stick”
This lab demonstrates inter-VLAN communication via the “Router on a Stick” method. To enable inter-VLAN communication, a trunk link is created between a router and switch. Trunk links can carry traffic for multiple VLANS. Trunk links can also be used … Continue reading
Posted in Cisco, Labs, Networking
Tagged Cisco, Cisco 2611 router, Cisco C3560G switch, Cisco WS-C3560G-24TS switch, inter-VLAN communication, ios, router, Router on a Stick, switch, trunk, trunk links, trunk port, trunk ports, Trunking, trunks, vlan
5 Comments
IPv6 Presentation at Sun Microsystems
On January 31st, 2009, at Sun Microsystems, I gave a presentation on IPv6 and the Hurricane Electric (HE) Tunnelbroker. The speech was given during the SupperHappyDevHouse 30 event and you can download the presentation slides here. The event attracted a … Continue reading
Twitter
LinkedIn
Youtube
RSS